Basic Info.
Product Description
performance parameter
PC board (endurance plate,PC endurance plate,PC sound barrier special board products)
(1) light transmittance: the light transmittance of P C plate can reach up to 89%, which can be similar to glass phase. UV coating plate in the sun will not produce yellowing, atomization, light transmission is not good, ten years after the loss of light is only 6%, PVC loss rate is as high as 15%-20%, glass fiber is 12%-20%.
(2) impact resistance: impact strength is 250-300 times of ordinary glass, 30 times of the same thickness acrylic plate, 2-20 times of toughened glass, with 3kg hammer two meters below the fall without cracks, there is a "not broken glass" and "ring steel" reputation.
(3) Light weight: the specific gravity is only half of glass, saving the cost of transportation, moving, installation and supporting frame.
(4) flame retardant: national standard GB50222-95 confirmed, PC board flammable level, that is, V2 level. PC board its own ignition point is 580 degrees Celsius, from the fire after self-extinguishing, combustion will not produce toxic gases, will not promote the spread of the fire.
(5) anti-ultraviolet: PC board coated with anti-ultraviolet (UV) coating on one side, the other side has anti-condensation treatment, set anti-ultraviolet, heat insulation and anti-drip function in a body. Can block ultraviolet through, and suitable for the protection of valuable art and exhibits, so that it is not damaged by ultraviolet light, ultraviolet (UV) protective film solar radiation has a clear harm to polymer materials, will cause the surface of fine lines cause degradation. These fine lines are susceptible to water, dust and water chemicals and erosion. The extent of these effects on the polymer is largely dependent on environmental parameters such as geographical location, altitude and seasonal variations. Hongsheng plate has one or two sides of ultraviolet protection layer, has good outdoor weather resistance. This unique protection ensures long-term use and retention of its optical properties under strong ultraviolet light irradiation, compared with other thermoplastic materials.
(6) Bendable: it can be installed into arch, semicircular roof and window by cold bending method on site according to the design drawing. The minimum bending radius is 175 times of the thickness of the plate. It can also be hot bent.
(7) sound insulation: PC board sound insulation effect is obvious, than the same thickness of glass and sub-afterforce plate has better sound, sound insulation, in the same thickness of the condition, PC board sound insulation than glass 3-4dB. It is the first choice material for sound barrier of highway in the world.
(8) energy saving: summer to keep cool, winter insulation, PC board is lower than ordinary glass and other plastic thermal conductivity (K value), heat insulation effect is higher than the same glass 7%-25%, PC board heat insulation up to 49%. So that the heat loss is greatly reduced, used for buildings with warm equipment, is an environmental protection material.
(9) temperature adaptability: PC board at -100 degrees Celsius does not occur cold brittle, at 135 degrees Celsius does not soften, in the harsh environment of its mechanics, mechanical properties, etc., there is no obvious change.
(10) weather resistance: PC board can be in the range of -40ºC to 120ºC to maintain the stability of the physical indicators. After 4000 hours of artificial climate aging test, the yellowing degree was 2 and the light transmittance decreased by only 0.6%.
(11) anti condensation: when the outdoor temperature is 0ºC, the indoor temperature is 23ºC, and the indoor relative humidity is lower than 80%, the inner surface of the material will not condensation.
| The proportion of | Specific gravity | g/cm3 | 1.2 |
| Light transmittance | Light transmission | % | 88 |
| The impact strength | impact strength | J/m | 850 |
| The bending strength | Flexural strength | N/(mm2) | 100 |
| The tensile strength | Tensile strength | N/(mm2) | >60 |
| Modulus of elasticity | Modulus of Elasticity | Mpa | 2400 |
| Tensile stress at break | Tensile strength at break | Mpa | >65 |
| Tensile strength at break | Elongation at break | % | >100 |
| Specific heat | Specific Heat Capacity | KJ/kg.K | 1.17 |
| Coefficient of thermal conductivity | Thermal Conductivity | W/m2.K | 0.2 |
| Thermal deformation temperature | Heat Deflection Temperature | ºC | 140 |
| Coefficient of thermal expansion | Coefficient of Linear Thermal Expansion | Mm/m.ºC | 0.067 |
| The use of temperature | Service Temperature | ºC | -40--120 |
| Sound insulation effect | Acoustic Insulation | 10mm solid sheet | 33db |
product picture
About our company
Q&A :
1. Q: Is your company a factory or trading company?
A: Our company is a professional manufactory.
2. Q: Where is your factory located? How can I visit there?
A: Our factory is located in No.1998 JinFeng South Road ,Mudu town,Wuzhong district ,Suzhou City ,Jiangsu,China . All our clients, from home or abroad, are warmly
welcome to visit our company!
3. Q: What's your MOQ?
A: For PVC rigid sheet, our MOQ is 0.5 Ton.
4. Q: What's your best price for PVC rigid sheet?
A: We will quote you best price based on your order quantity. So please advise the
order quantity when you make an inquiry.
5. Q: How can I order samples?
A: We can provide FREE samples if you can take care of the expressing freight. So
please provide your own expressing account (such as DHL, TNT, UPS etc.) for
sample expressing freight collected. The freight cost can be refunded to you if you
can place an order from us then.
6. Q: How to pay for the products?
A: Our regular payment terms are T/T or Irrevocable L/C at sight.
7. Q: What's your delivery time?
A: The delivery time is about 7-15 days after receiving your deposit payment.